Keywords and phrases: short fiber, orientation, polymer, numerical simulation, Runge-Kutta method thermoplastic, Folgar, Tucker, Jeffery.
Received: February 1, 2023; Revised: February 22, 2023; Accepted: March 23, 2023; Published: June 17, 2023
How to cite this article: I. Modhaffar, K. Gueraoui, M. Taibi, H. El-Tourroug and S. Men-La-Yakhaf, Theoretical and numerical analyses of short natural fibers orientation in thermoplastic matrix, International Journal of Materials Engineering and Technology 22(1) (2023), 55-83. http://dx.doi.org/10.17654/0975044423005
This Open Access Article is Licensed under Creative Commons Attribution 4.0 International License
References:
[1] G. B. Jeffery, The motion of ellipsoidal particles immersed in a viscous fluid, Proceedings of the Royal Society of London, Series A 102(715) (1922), 161-179. [2] G. G. Lipscomb, Analysis of suspension rheology in complex flows, Ph.D. dissertation, University of California, Berkeley, 1987. [3] M. Vincent, E. Devilers and J. F. Agassant, Fiber orientation in injection molding of reinforced thermoplastics, Journal of Non Newtonian Fluid Mechanics 73 (1997), 317-326. [4] F. Folgar and C. L. Tucker, Orientation behavior of fibers in concentrated suspensions, J. Reinf. Plast. Compos. 3 (1984), 98-119. [5] S. Prager, Stress-strain relation in a suspension of dumbbells, Trans. Soc. Rheol. 1 (1994), 53. [6] G. L. Hand, A theory of anisotropic fluids, J. Fluid Mech. 13 (1962), 33-46. [7] R. S. Bay, Fiber orientation in injection-molded composites: a comparison of theory and experiment, Ph. D. dissertation, University of Illinois at Urbana-Champagne, 1991. [8] C. Carrot and J. Guillet, Viscoélasticité non linéaire des polymères fondus, Traité Plastiques et Composites, 1999. [9] A. Chapman, Y. Saad and L. Wigton, High order ILU preconditioners for CFD problems, Rapport technique, AMSI, Minnesota Supercomputer Institute, 1996. [10] A. J. Chorin, Numerical solution of the Navier-Stokes equations, Math. Comp. 22 (1968), 745-762. [11] S. G. Advani and C. L. Tucker, A numerical simulation of short fiber orientation in compression molding, Polym. Compos. 11 (1990), 164-173. [12] M. C. Altan, S. Subbiah, S. I. Guceri and R. B. Pipes, Numerical prediction of three dimensional fiber orientation in Hele-Shaw flows, Po1ym. Eng. Sci. 30 (1990), 848-859. [13] I. Modhaffar, K. Gueraoui, H. El-Tourroug and S. Men-La-Yakhaf, Numerical study of short fiber orientation in simple injection molding processes, AIP Conf. Proc. 1653 (2015), 020071. [14] I. Modhaffar, K. Gueraoui, S. Men-La-Yakhaf, H. El-Tourroug, M. Taibi, M. Driouich, M. Sammouda and M. Belcadi, Simulation and prediction of the orientation of short fibers polypropylene injected into a matrix with the imaging technique (HFSP), to appear. [15] J. C. Halpin and J. L. Kardos, Strength of discontinuous reinforced composites: 1 fiber reinforced composites, Polym. Eng. Sci. 18 (1978), 496-500. [16] S. H. McGee, The influence of microstructure on the elastic properties of composite materials, Ph. D. Thesis, University of Delaware, Newark, 1982. [17] I. Modhaffar, K. Gueraoui, S. Men-La-Yakhaf and H. El-Tourroug, The effect of orientation of short fibers in the diluted suspension for thermoplastic, International Review of Mechanical Engineering (IREME) 10(1) (2016), 7-11. [18] A. Clarke, N. Davidson and G. Archenhold, Measurements of fibre direction in reinforced polymer composites, Journal of Microscopy 171(1) (1993), 69-79. [19] C. Eberhardt and A. R. Clarke, Fibre orientation measurements in short glass fiber composites: I automated high angular resolution measurement by confocal microscopy, Composite Sciences Technology 61 (2001), 1389-1400. [20] S. Men-La-Yakhaf, K. Gueraoui and M. Driouich, New numerical and mathematical code reactive mass transfer and heat storage facilities of argan waste, Advanced Studies in Theoretical Physics 8(10) (2014), 485-498. [21] H. El-Tourroug, K. Gueraoui, N. Hassanain, I. Modhaffar and S. Men-La-Yakhaf, Numerical and mathematical modeling of the injection for incompressible fluids through rigid cylindrical duct: application of melted polymers PPH, Appl. Math. Sci. 8(180) (2014), 8953-8964. [22] I. Modhaffar, K. Gueraoui, S. Men-La-Yakhaf and H. El-Tourroug, Simulation study for prediction of short fiber orientation reinforced thermoplastics, Materials Today: Proceedings 3 (2016), 2891-2897. [23] S. Men-La-Yakhaf, K. Gueraoui, A. Maaouni and M. Driouich, Numerical and mathematical modeling of reactive mass transfer and heat storage installations of argan waste, International Review of Mechanical Engineering (IREME) 8(1) (2014), 236-240.
|